超声波在液体中传播，可以使液体与清洗槽在超声波频率下一起振动，达到洁净的效果，在此过程中，液体与清洗槽振动时有自己固有频率，这种振动频率被称为声波频率。近年来，随着清洗行业的不断发展，越来越多的行业和企业运用到了超声波清洗机。

When the ultrasonic wave propagates in the liquid, the liquid and the cleaning tank can vibrate together at the ultrasonic frequency to achieve the clean effect. In this process, the liquid and the cleaning tank have their own natural frequency when they vibrate, which is called the acoustic frequency. In recent years, with the continuous development of cleaning industry, more and more industries and enterprises use ultrasonic cleaning machine.

与一般的清洗方式相比，超声波清洗器具有清洗效果好、操作便捷等优点，因此也深受客户推崇。好的产品需要合适的操作方法才能达到事半功倍的效果。小编整理了一份关于超声波清洗器的操作方法，需要的客户可进行参考。

Compared with the general cleaning method, the ultrasonic cleaner has the advantages of good cleaning effect and convenient operation, so it is highly praised by customers. Good products need appropriate operation methods to achieve twice the result with half the effort. Xiaobian collates an operation method of ultrasonic cleaner, which can be referred by customers who need it.

首先，参照超声波清洗机安装说明书连接清洗机的电控柜与主机间的温控传感器信号线、超声驱动线、加热器控制线等线路，并接通380VAC电源，安装清洗机的上水管、放水管与溢流排放管，保证机器的正常运转。

First of all, according to the installation instructions of the ultrasonic cleaning machine, connect the temperature control sensor signal line, ultrasonic drive line, heater control line and other lines between the electric control cabinet and the main machine of the cleaning machine, and connect the 380VAC power supply, install the water supply pipe, water discharge pipe and overflow discharge pipe of the cleaning machine, so as to ensure the normal operation of the machine.

随后，用户应向清洗池内加入适量清水，通常情况下液面高度以浸没将要清洗的零部件为准，一般不超过清洗池的四分之三。在启动电控加热开关后，将水温调节旋钮上的白色刻度线指向适当的温度(应为60℃左右)。需要注意的是，清洗机在使用过程中，清洗剂的高温度不能超过70℃。

Then, the user should add an appropriate amount of clean water to the cleaning pool. Under normal circumstances, the liquid level is subject to the immersion of the parts to be cleaned, generally not more than three-quarters of the cleaning pool. After starting the electric heating switch, point the white mark on the water temperature adjusting knob to the appropriate temperature (about 60 ℃). It should be noted that the maximum temperature of the cleaning agent should not exceed 70 ℃ during the use of the cleaning machine.

当水温升至40℃左右时，将特定清洗剂加入清洗池中(一般一次5kg左右)，慢慢搅动清水使两者充分溶解，方可开始清洗之旅。

When the water temperature rises to about 40 ℃, add the specific cleaning agent into the cleaning pool (usually about 5kg at a time), and slowly stir the clean water to fully dissolve the two, then the cleaning journey can begin.

除此之外，超声波能够进行精密清洗，但其对泥类的污物处理能力较弱，故预处理中，应尽量将用竹刀先将零部件表面的污垢(如防尘罩外表面会有很多尘土、气缸体类的零件在其外壳曲线变化处会积留很多厚且易除的油泥)简单清洁一下，以便延长清洗液使用寿命。

In addition, ultrasonic can carry out precision cleaning, but its ability to treat sludge is weak. Therefore, during the pretreatment, the dirt on the surface of parts (for example, there will be a lot of dust on the outer surface of the dust cover, and there will be a lot of thick and easy to remove oil sludge on the curve change part of the cylinder block) should be cleaned simply with a bamboo knife, In order to extend the service life of the cleaning solution.